Silhouette roll feeder 2017

ROLL FEEDER SET UP

The first thing we have to do is add the Silhouette roll feeder to the Shape device. The recommendations show how to try this, and the pockets are revealed about the feeder. If you’re currently deploying it using the CAMEO fall into line those two commonly-spaced square holes with the feet of the CAMEO and simply fall the toes into the pockets. This guarantees the move feeder is properly put against the equipment.
It is possible to cut vinyl rolls -inch with the vinyl feeder. Just slip the proper-palm information of the feeder into either position and fixed the move of plastic in-place.

HINT: I’ve discovered the feeder is best suited with moves that have a tough inner-tube, as opposed to merely a roll of vinyl without any cardboard tube inside.

Make sure to change the white wheels in your CAMEO, as well. Pull-down the change lever, adjust the right-hand roller for the 12” location (one step in), then force the change lever straight up again.
Be sure to lean the key edge of the vinyl so it’s right before running the vinyl and is perpendicular to its side edge. You need to use the cutter that’s included with your favorite straight-edge or the spin feeder trimmer.

TIP: I also prefer to bend the best edge up of giving it through the CAMEO and also the spin feeder for that ease. Coming from a roll it tends to bend along, so simply curl it a little while in the reverse direction.

To insert the plastic with the move feeder, location the throw so its leading edge covers the most effective of the spin towards the device, then give it under the front bright opening (see photograph below).
Eventually, fill the vinyl to the CAMEO. Your vinyl should be absolutely holding the machine’s rollers on both sides and also the roller change handle must be in the up location. Support the plastic contrary to the rollers while selecting “Load Media” (not weight cut pad).

Silhouette-roll-feeder

CUT YOUR VINYL

The next step will be to lower on your plastic. Since my material section was 16 in. x-20 in., I used almost vinyl’s total 12 in. width available to me. My layout was resized by me to 11.5 in. wide to give a little area for the wheels across the tips. You can observe how I create my workspace and Style Page Controls in Outline Studio®.
• Test rectangle to represent my fabric of 16 in. x 20 in. (positioned outside the cutting place)
• Style sized to 11.5 in.-wide (placed on the rectangle to obtain an idea of how it’ll appear)
• Repeat of design to cut positioned on cutting on area of workspace
• Page Size = 12 in. x-20 in. (the size concerns, however not always the duration since we’re reducing from a throw)
• Slicing Mat = none
• Examine “Show Reduce Border”
• Then I cut my plastic with my pre-tried options (Blade 2, Pace 9, Breadth 8) therefore it would lower completely through the plastic however not through the backing.

Just sell it from the machine • Following The design has been cut and cut removed it from the move.Our design was but with the roll feeder you can easily cut at nearly the whole length of the throw.

 

WEED YOUR VINYL

• Next, filter your plastic together with the hook software by disposing and selecting of every one of the extra vinyl around and throughout your layout.

TRANSFER YOUR DESIGN TO YOUR PREPARED AREA

Now it’s time for you to apply the vinyl for the prepared floor. Since I used 12-inch vinyl, I also used 12-inch transfer paper.

Slice the transfer paper to complement the vinyl design that is weeded.

My trick for implementing move paper to your significant layout would be to extend down about an inchroughly of the backing at the top fringe of the move report, then carefully make and click along that top inch of transport paper towards the vinyl design’s top edge of backing. Once that’s secure, you can peel the transport paper’s backing away from underneath while removing the transport document along the plastic layout.
Make use of the scrape device to press and rub the full design permanently adhesion when the transfer document is since the vinyl design.

Now position the exchange report and design to the organized area. Use a painter’s and ruler tape to assist have it right.
Once you’re confident of the position, employ painter’s tape at the top (include more if required) to behave just like a joint so you can start pulling away the vinyl’s backing in the top and function your way along. Push the vinyl layout (about the transport report) against the area when you peel-away the backing from underneath.
Use the scrape again to press on the plastic layout against the fabric panel, then carefully peel away the transfer paper as the vinyl layout remains in position.

Leave a Reply

Your email address will not be published. Required fields are marked *